0 Items

Chains and their Types two

Leaf chains

Leaf chains are used nearly exclusively for lifting and counterbalancing. Tensions are very high, but speeds are sluggish. Normally the chains function intermittently. The main factors in the design of the leaf chains are tensile loads, joint wear, and link plate and sheave use.

The major dimensions of standard leaf chains are proportional to the chain pitch. These proportions are derived from engineering studies and encounter. The typical proportions give a good stability of properties needed for a leaf chain to lift large loads while offering suitable wear life.

The most common use for leaf chain is most likely on lift trucks. A leaf chain used on a lift truck is generally under a considerable static load from the trucks lifting carriage. In addition, the chain withstands the nominal operating load from transporting the material. It also absorbs shock loads from shifting material over uneven areas, and withstands inertia loads from picking right up the material to be shifted.

Just as with roller chains, leaf chains are to have a certain minimum supreme tensile strength (UTS). That is because yield power (YS) and Description and features of air compressor fatigue power (FS) are usually related to tensile power. However, UTS is not to be utilized for choosing leaf chains since it can mislead into overloading of the chain.

Yield strength is the major account while designing leaf chains. Leaf chains must frequently lift very large loads, and hence they need high YS , nor get completely stretched if they lift huge loads.

FS is also a major consideration in designing leaf chains. Leaf chains move at low speeds and accrue load cycles extremely slowly. Because so many leaf chains function in the finite-lifestyle range (between 10,000 and 1,000,000 cycles), therefore FS in this range is very important.

The fatigue limit (FL) is moderately important in the design of leaf chains, due to the fact FS in the finite-life range is related to the FL. It is also because leaf chains accrue load cycles very slowly.

Wear is an extremely important consideration even though developing leaf chains. Leaf chains are mainly subjected to joint put on and link plate/sheave wear. Both of these wears decrease the power of leaf chains.

Joint wear is important for developing leaf chain. Whenever a leaf chain runs over sheaves, the joints articulate. Materials is put on off the exterior diameter of the pins and the inside size of the holes in the articulating link plates. As the material is worn apart, the chain not only gets longer, however the load-carrying sections of the pins and articulating hyperlink plates get smaller.

Link plate put on, from running more than sheaves, can be important consideration for the look of a leaf chain while the sheave use is normally not a major consideration.

The lubrication is a serious concern in the design of leaf chains. Some leaf chains receive little or no lubrication operating, and the developer is to consider this.

The environment in which a leaf chain works is a serious concern in the look of leaf chains. Many leaf chains are not protected in any way from the encompassing environment. Many leaf chains work outdoors in all kinds of weather.

Leaf chain can be an assembly of alternating units of pin links and articulating links in pins that are absolve to articulate in the holes of the articulating links. The pin web page link plates normally are press installed onto the ends of the pins in the chain. The center hyperlink plates are often slip installed on the pins. Leaf chains are intended to stepped on sheaves, therefore there is no provision to allow them to engage a sprocket.

A clevis pin can be used to connect the finish of a leaf chain to an outside clevis. The exterior clevis gets its name because the outer tangs of the clevis suit beyond the articulating link plates of the chain

A connecting link can be used to connect the finish of a leaf chain to an inside clevis. The inside clevis gets its name since the external tangs of the clevis in good shape within the chain. The connecting link includes two linking pins press fitted into one pin hyperlink plate, the required number of center hyperlink plates, and a cover plate. Either cotters or a spring clip can be used to carry the cover plate set up. The cover plate is to be an interference fit on the pins to provide the connecting link about the same power as the pin links in the chain.

Leaf chain is a rather basic lacing of pins and link plates. Operating forces are transmitted from the clevis pin or connecting link to the articulating hyperlink plates. The articulating link plates after that transfer these forces to the next pin, which transfers the forces to the pin hyperlink plates and Chains and their Types   two - 8162centre plates. And then the sequence repeats.

Some parts have to perform several functions simultaneously. For example, the articulating link plates need high hardness to resist wear, and also need great ductility to endure huge shock loads. The developer is to decide how to utilize these conflicting requirements.

The tension forces on a leaf chain subject the pins to mostly shear with some bending, and they do so while the pins submit the articulating link plates. The pins act as both beams and bearings in a leaf chain. The pins want enough strength and ductility to transfer the load from the articulating link plates to the pin link plates and centre plates without deforming or breaking. The pins also need high enough surface hardness to withstand wear when the joint articulates under heavy loads.

The pin link plates in a leaf chain are mostly tension members, however they are also subjected to some bending. The holes in the pin hyperlink plates are significant tension risers that produce high tension concentrations around the holes. The pin link plates should be strong more than enough to withstand the tensile forces without deforming or breaking, and they must have enough ductility to withstand some bending and resist fatigue. The holes should be made with some particular processing to withstand fatigue.

The centre link plates in a leaf chain are almost totally tension members. They are put through hardly any bending. The holes in the centre link plates are significant tension risers that generate high tension concentrations around the holes. The centre link plates are to be strong plenty of to endure the tensile forces without deforming or breaking, and they must have plenty of ductility to resist exhaustion. The holes should be made with some unique processing to withstand fatigue.

The articulating link plates in a leaf chain are almost totally tension members. They are subjected to hardly any bending. The holes in the articulating link plates are significant stress risers that produce high tension concentrations around the holes. In addition, the articulating link plates must transmit very high tensile forces while a pin turns in the holes of the link plate. The articulating hyperlink plates may be the most significant parts in a leaf chain. They are to be strong enough to withstand the tensile forces without deforming or breaking, plus they must have enough ductility to resist exhaustion. The holes must be made with much particular processing to withstand fatigue. Finally, the articulating hyperlink plates must be hard enough to resist put on when the pin turns in the holes under high loads.

Silent chains

Silent chain, also called ‘inverted tooth’ chain, contains a number of toothed link plates assembled on joint components in a manner that allows free flexing between each pitch. Almost all of silent chain is used in drives. Silent chains are made of stacked rows of load transporting link plates. Raising the amount of rows of links increases the chain width, tensile power, and load carrying capacity.

Silent chains are made of stacked rows of toned link plates with gear-type contours designed to engage sprocket teeth in a manner like the way a rack engages a equipment. The links are held collectively at each chain joint by one or more pins, which also permit the chain to flex. The look of both hyperlink contour and the chain joint directly influences a chain’s useful load carrying capacity, its rate of put on and service lifestyle, and its own quietness of procedure.

Silent chains from different producers usually cannot be connected together. Standard silent chains are found in a wide variety of industrial drives where a small, high-speed, simple, low-noise get is required.

There are many classes of silent chains, which are not produced by all the manufacturers and are not covered by any standard. Even so, these particular silent chains meet important requirements. The most typical nonstandard silent chains are most likely the high-performance travel chains. High-functionality silent chains are specially designed to carry better loads and run at higher speeds than standard silent chains. They often have unique joint styles with rocker-type pins that virtually eliminate chordal actions. They usually require specifically designed sprockets. Powerful silent chains can be found in a wide range of sizes with pitches and in widths and so are used on very-high-rate drives where exceptional smoothness and quietness are required. These chains are commonly used in industrial equipment where best smoothness is necessary.

Other nonstandard silent chains are duplex, conveyor, and specialty chains. Duplex silent chains have teeth extending on both sides of the pitch series allowing the chain to run on serpentine drives where sprockets engage both sides of the chain.

Conveyor silent chains often use flat-back hyperlink plates that provide a clean conveying surface area and may use joint styles that resist fouling. Conveyor silent chain is generally used where remarkably smooth transportation is necessary. Specialty silent chains are created for particular applications where accessories or unusual configurations are required.

Engineering steel chains

Engineering metal chains were first created in the 1880s. These were created for greater strength, swiftness, and shock resistance, and for better dimensional control. Early engineering steel chains were made for tough conveying applications. Just as with roller chains, engineering metal chains were created as all-steel products fabricated from rolled designs. One exception was that rollers, especially flanged rollers, had been manufactured from cast iron, which exception has continued to the present.

Bigger sizes of engineering steel chains were quickly developed. Pitch, strength, wear existence, and carrying capability were increased to meet up with the heavy-duty requirements of sector. Engineering steel chains were developed to use dependably in the most demanding conditions.

Many different types of engineering steel chains are found in a wide variety of applications. Many engineering steel chains are used in conveyors, bucket elevators, and pressure linkages. Only a few are found in drives. The main design factors for these chains are tensile loads, several types of put on, lubrication, and environment. The main design considerations for an engineering metal chain to be utilized on a get include the numerous tensile loads, certain types of wear, roller and bushing impact, and galling.

The dimensions of engineering steel conveyor chains are not proportional to the pitch. Engineering metal chains generally possess much bigger clearances between shifting parts than roller chains of the same size. The clearances between the pins and bushings, the bushings and rollers, and the internal and outer links are proportionally much larger. The larger clearances are provided to ensure that dirt and debris can pass openly out from the bearing areas. The debris is, thus, not as likely to clog the joints of the chain, causing them to bind or seize.

An engineering steel chain in a conveyor or drive may be subjected to all of the tensile loads. However, the tensile loads from centrifugal push, chordal action, and vibration are not very likely to become a major factor. Thus, engineering metal chain will need to have certain tensile power properties to withstand the wide selection of tensile loads which may be imposed on it.

Ultimate tensile strength is not a major consideration in designing engineering steel chains. That is because YS and FS are just generally related to UTS. Yield power is a significant consideration in creating engineering metal chains. FS in the finite-life range is a very important while creating engineering metal chains. Loads occasionally exceed the FL in some seriously loaded conveyors and drives.

The FL usually isn’t critical for the design of engineering steel chains. It is because most of the engineering metal chains accrue cycles extremely slowly and these chains are anticipated to degrade before fatigue can cause the chains to fail.

Wear is most likely the most important parameter while designing an engineering steel chain. Joint use, roller and bushing wear, and sidebar and track wear all are of great concern for conveyor chains. Joint put on and roller and sprocket put on are the major problems for drive chains. As the chain runs over the sprockets, the joints articulate and materials is worn off the outside size of the pins and the inside diameter of the bushings, and as this materials is worn apart, the chain gets longer

Sprockets for engineering steel chain are made to accept chain elongation from wear of 3 % to 6 %. When the chain elongates beyond this point, it no more fits the sprockets and the machine will not operate properly.

Roller wear in travel chains usually is not a major concern, but roller use in conveyor chains may be a significant concern. Put on of one’s teeth on a little sprocket can impose large shock loads on the chain. Roller and bushing wears, and sidebar and monitor wears are very important factors in the look of engineering steel roller conveyor chains.

Lubrication is a major concern in developing engineering steel conveyor chains. Many engineering metal conveyor chains must work with little or no lubrication, and thus materials selection is essential.

Environment is a significant concern in developing engineering steel conveyor chains. Standard conveyor chains are to work in mildly corrosive circumstances. Some conveyor chains are also to function in extremely abrasive circumstances. Highly abrasive circumstances are typically found in mining and material handling. Extreme temps are usually not a major concern in developing standard engineering metal chains.

There are plenty of general types of engineering steel chains. People that have metal rollers are perhaps the most widely used on both drives and conveyors. The bushed, roller-less style meets the needs of several conveyor and bucket elevator applications. Welded metal versions of the essential cast chains are actually quite popular, and a straightforward bar-hyperlink type can be used for slow-moving conveyors and pressure linkages.

Stress linkage chains are a series of chain items that are both catalog standard and produced for special purposes. The main utilization of a tension linkage chain can be to move lots gradually or intermittently over a given distance. In addition they are used to reliably keep a load in position when it is not moving. Pressure linkage chains generally move backwards and forwards instead of through a complete revolution.

Tension linkage chains are used in a number of ways. They might be used for hoisting, supporting counterweights, or pulling items through forming operations. The loads in these applications can range from a few grams to many tons. The wide variety of loads needs many different sizes and types of items to meet the various requirements.

Uses of chains

The major uses of the various types of chains are in drives (power transmission), conveyors, bucket elevators, and tension linkages. Some regular chains are created for use in mere among these applications. However, some chains were created therefore that they can be adapted to several use.

Roller chains and engineering metal chains are found in all types of applications. Leaf chains are utilized almost specifically for lifting and counterbalancing. Silent chain is essentially for get applications, although a few conveying applications can be found. Flat-top chain is supposed limited to conveying.

Contact us for More information → https://www.ever-power.net/contact-us/

You are always welcome to ask any information! Please feel free to contact us!

Request a quote

If you have any request, please fill this form and we will reply you within 24 hours.


1. Stainless Steel: SS201, SS303, SS304, SS316, SS416, SS420
2. Steel:C45(K1045), C46(K1046),C20
3. Brass:C36000 ( C26800), C37700 ( HPb59), C38500( HPb58), C27200(CuZn37), C28000(CuZn40)
4. Bronze: C51000, C52100, C54400, etc
5. Iron: 1213, 12L14,1215
6. Aluminum: Al6061, Al6063
7.OEM according to your request


Annealing, natural canonization, heat treatment, polishing, nickel plating, chrome plating, zinc plating,yellow passivization, gold passivization, satin, Black surface painted etc.


CNC machining, punch,turning, milling, drilling, grinding, broaching, welding and assembly


Technicians self-check in production,final-check before package by professional Quality inspector

ISO9001:2008 , ISO14001:2001,ISO/TS 16949:2009


Size: Drawings

Wooden Case/Container and pallet, or as per customized specifications.

15-25days samples. 30-45days offcial order

Related Searches:

Nullam luctus fringilla mi, felis id Curabitur velit, Donec et, massa dolor

Pin It on Pinterest

Share This